Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Bis-(monoacylglyceryl) phosphate and acyl phosphatidylglycerol isolated from human livers of lipidosis induced by 4,4′-diethylaminoethoxyhexesterol

Bis-(monoacylglyceryl) phosphate and acyl phosphatidylglycerol were isolated from the liver of two patients with lipidosis induced by 4,4′-diethylaminoethoxyhexesterol. Identification was based upon the results of alkaline hydrolysis, acetolysis, IR spectrometry, and upon the determination of molar ratio of phosphorus-glycerol-ester. The contents of the bis-(monoacylglyceryl) phosphate were 10 and 16% total phospholipid phosphorus in them. The bis-(monoacylglyceryl) phosphate contained mainly docosahexaenoic (42%), oleic (29%), and linoleic acid (14%) and had the hemolytic activity of ca. one-eighth lysolecithin from egg yolk. Acidic lipids from the liver also were found to contain a lipid which is less polar than bis-(monoacylglyceryl) phosphate. The results of lipid analysis showed that the lipid possessed the structure of an acyl phosphatidylglycerol, and its content was ca. 2% total phospholipid phosphorus. Accumulation of 4,4′-diethylaminoethoxyhexesterol and its derivatives was found in clinical cases by thin layer chromatography and IR spectrometry. This fact suggested that human liver has an ability to metabolize the drug.     

Lyapunov-based feedback design and experimental verification of IC engine speed control

In this paper, the speed control problem of internal combustion engines is investigated based on mean-value engine models. The dynamics of internal combustion engines is a complicated nonlinear system, and usually, it is difficult to know the exact values of the physical parameters. First, a Lyapunov-based design method is shown without requiring the full information of the physical parameters. Then, to improve transient performance, the design method is extended to several cases under different operation conditions. Numerical simulation results are presented for comparing the proposed design methods. Finally, experiments are conducted on an engine test bench and the results demonstrate the validity of the proposed design methods. Recommended by Editorial Board member Myotaeg Lim under the direction of Editor Hyun Seok Yang. The authors are grateful to Kai Zheng for his assistance of the model identification experiments. Jiangyan Zhang received the B.E. and M.E. degrees in Electrical Engineering, Yanshan University, China, in 2005 and 2008, respectively. Now, she is a Ph.D. candidate with the Department of Engineering and Applied Sciences, Sophia University, Tokyo, Japan. Her current research interests include nonlinear system control theory and applications to powertrain system control. Tielong Shen received the Ph.D. degree in Mechanical Engineering from Sophia University, Tokyo, Japan, March, 1992. From April 1992, he has been a faculty member of the Chair of Control Engineering in Department of Mechanical Engineering, Sophia University, where he currently serves as professor of the Department of Engineering and Applied Science. His research interests include control theory and application in mechanical systems, power systems, and automotive powertrain. Currently, he is an Associate Editor for the IEEE Control System Society Conference Editorial Board, and is serving as Associate Editor of Journal of Control Theory and Applications, and the Regional Editor Asia-Pacific for International Journal of Modeling, Identification and Control etc. Junichi Kako received the B.E. degree from Nagoya Institute of Technology, Nagoya, Japan. He joined Toyota Motor Corporation, Tokyo, Japan in 1989. He worked on various aspects of automotive powertrain control. From 1989 to 1994, he took part in the team for the development of Laboratory Automation (LA) system, Engineering Office Automation (EOD) system, and embedded system of powertrain control. During 1995–2001, he focused on the engine control systems in Powertrain Management Engineering Division. In 2002, he was with Future Project Division in which he was responsible for the R&D of model-based engine control system. Currently, he is developing engine control systems in the Powertrain Management Engineering Division, Toyota Motor Corporation. Shozo Yoshida received the M.S. degree in Engineering from Kyoto University, Kyoto, Japan. He joined Toyota Motor Corporation, Tokyo, Japan in 2000. From 2000 to 2004, he was with Future Project Division and worked on physical combustion modeling for Model-based Control Development. Since 2005, he has been with the Powertrain Management Engineering Division Toyota Motor Corporation, and is a member of the R&D of Model-based Engine Calibration.     

Thermomechanical behavior of Ti-Ni shape memory alloy films deposited by DC magnetron sputtering

In this study, thermomechanical properties of titanium-nickel (Ti-Ni) shape memory alloy (SMA) films are investigated in order to derive constitutive relations. Ti-Ni SMA films, deposited by DC magnetron sputtering under controlled film composition, are characterized by uniaxial tensile tests. At room temperature (R.T.), Ti-Ni films having Ti contents less than 50 at% exhibit superelastic behavior, and those having Ti contents greater than 50 at% exhibit shape memory behavior. However, the Ni—53.2 at% Ti film fractured at a tensile strain of 0.8% because of an increase in brittleness with increasing Ti content. At elevated temperatures, Ti-Ni films having Ti contents of 50.2 to 52.6 at% undergo phase change from martensite to austenite. The Young's modulus of the Ti-Ni films depends on temperature at each phase, regardless of film composition. Film composition does, however, affect the measured material constants b_A, b_M, c_A, and c_M. Stress-strain curves calculated from the constructed constitutive equation closely agree with those obtained from tensile tests, for both the martensite and austenite phases. The constitutive equations are expected to find great utility in the design of Ti-Ni film-actuated microelectromechanical systems (MEMS).     

Towards the improvement of thermal efficiency in lignite‐fired power generation: Concerning the utilization of Polish lignite deposits in state‐of‐the‐art IGCC technology

Integrated coal Gasification Combined Cycle (IGCC) is the most advanced technology for coal‐fired power generation. The two‐stage entrained flow gasification process allows for the use of a wide range of coal, as long as the gasification temperature is above the ash melting point of a used fuel. In this gasification technology, lignite, which often has a low ash melting point, can be preferably utilized. However, ash fluidity is also another importance, because the behaviour of molten slag can diminish a stable ash discharge from a gasifier. As the eligibility of coal ash properties is a considerable factor, water physically and chemically kept in lignite (30 – 60% in mass) attributes to deteriorating gasification efficiency, because it causes significant heat loss and increasing oxygen consumption. Developing a thermal evaporative lignite drying method will be a necessary attempt to apply lignite to the coal gasification process. For those preceded objectives, coal and ash properties and drying characteristics of several grades of Polish lignite, extracted from Belchatow and Turow deposits, have been experimentally investigated in a preliminary study evaluating the applicability and consideration for its utilization in state‐of‐the‐art clean coal technology, IGCC. This paper particularly discusses the eligibility of Polish lignite from the perspective of the fusibility and fluidity of ash melts and the fundamental drying kinetics of lignite in superheated steam in the light of water removal. The viscosity of ash melts is measured at high temperature up to 1700 °C. In the drying tests, the significant influence of structural issues, because of the provenance and origin of lignite on the drying characteristics, was found by applying the method of sensitivity analysis of physical propensity. This paper concludes that the investigated Polish lignite has characteristics favourable for utilization in IGCC technology, once the precautions related to its high moisture have been carefully addressed. Copyright © 2016 John Wiley & Sons, Ltd.     

Moderately high speed impact of two identical spheres

This paper deals with impacts between two identical spheres in moderately high speed range. Impact of spheres is one of basic problems in mechanical dynamics. Severity of impact is generally characterized by the coefficient of restitution. However, influence of material property on the coefficient of restitution has not been clarified yet. The authors previously investigated direct central impacts of two identical spheres in low speed range and revealed that strain rate sensitivity of material properties could not be ignored even in the low speed impacts. Therefore, this paper investigates the direct central impact of two identical spheres in higher speed range. The impact experiments were performed in range of impact speed 10 m/s–20 m/s by using air-gun setup. It was confirmed that the expressions for the coefficient of restitution and the contact time derived from the low speed impact remained effective in the moderately high speed range. Then numerical simulations by using Finite Element Method (F.E.M) have been carried out, in which the material properties and the strain rate effect were taken into account. The coefficient of restitution, contact time, sphere’s compression and contact circle diameter obtained by experiments and F.E.M. were compared and they matched well. Contact pressure distributions at maximum contact force were investigated. The contact pressure at sphere center varied little with impact speed but the contact pressure increased with impact speed near contact edge. Theoretical expression for prediction of the coefficient of restitution proposed by C. Thornton was examined to the experimental results of this study. To provide an accurate prediction, it is necessary to estimate the contact pressure depending on material properties. Finally, the Meyer analysis was applied to the case of this study and it was found that the Meyer’s law holds in the moderately high speed impact between two identical spheres.     

下一个! 通向未来的上海

文章希望在包容历史与未来这一方面,上海能成为建立起建筑新秩序的都市。     

Preparation and evaluation of gel formulations for oral sustained delivery to dysphagic patients

Background: Oral sustained release gel formulations may provide a means of administering drugs to dysphagic and geriatric patients who have difficulties with handling and taking oral dosage forms. Aim: We have designed gel formulations for the oral administration of paracetamol with suitable rheological characteristics for ease of administration to patients with swallowing difficulties and sufficient integrity in the acidic environment of the stomach to achieve a sustained release of this drug. Method: Gels formed by gelatin, agar, gellan, pectin, and xyloglucan were assessed for suitable gel strength and in vitro and in vivo release characteristics. Results: Gellan (1.5%?w/v) and xyloglucan gels (1.5%?w/w) had acceptable gel strengths for ease of swallowing and retained their integrity in the rat stomach sufficiently well to sustain the release of paracetamol over a period of 6 hours. Comparison of 1.5%?xyloglucan gels with a commercially available preparation with identical paracetamol concentrations demonstrated improved sustained release properties of the xyloglucan gels. Conclusions: Gels formed by gellan and xyloglucan have suitable rheological and sustained release characteristics for potential use as vehicles for oral delivery of drugs to dysphagic patients.     

In vivo immunological toxicity in mice of carbon nanotubes with impurities

The longstanding question as to whether carbon nanotubes are intrinsically toxic hinders their widespread industrial application. Here, we clarify the effect of impurities within such tubes through systemic studies of immunological responses in mice by monitoring and examining changes in peripheral T-cell subset and peripheral cytokine levels and histology. Contaminated and clean tubes were subcutaneously implanted in mice. The implanted tubes with impurities clearly induced immunological toxicity and localized alopecia, whereas extremely pure implanted tubes showed good biocompatibility. Our studies suggest that such high-temperature thermal treatment is an effective way to improve the biocompatibility of carbon nanotube.